The Impact of Gradation and Fineness Modulus of Recycled Mortar Sand on the Performance of Cement

AUTHOR(S)

Ganesh Tapkire, Dr. Shashi Ranjan kumar

DOI: https://doi.org/10.46647/ijetms.2023.v07i02.048

ABSTRACT
The fine coefficient is one of the physical properties of the fine aggregate. The fineness modulus (FM) is obtained by adding the total percentage of sand retained on each sieve and dividing by 100. The fineness factor varies depending on the resources available. Sand is widely used in construction. Due to excessive use, the supply of sand is decreasing day by day, is it necessary to find an alternative material for sand in the future? And on the other hand, the amount of construction and demolition waste is increasing every day and is still underutilized, and this is the main focus of research on the use of C and D waste mortar material in conventional construction. To analyse the waste mortar material, a material sample is collected from the site and the physical properties of the sand are checked and compared with the standard zones of sand according to the compressive strength IS using C and D waste mortar mixture in a ratio of 1:3 Casting. The 7.06 cm cube size is compared to 3-day and 7-day strength.
Page No: 403 - 409

References:

G. Sabih, R. A. Tarefder, and S. M. Jamil, “Optimization of Gradation and Fineness Modulus of Naturally Fine Sands for Improved Performance as Fine Aggregate in Concrete,” Procedia Eng., vol. 145, pp. 66–73, 2016, doi: 10.1016/j.proeng.2016.04.016.

T. Note, “AN EXPERIMENTAL INVESTIGATION ON PROPERTIES OF c r v i h o e f.”

B. P. Gautam, D. K. Panesar, S. A. Sheikh, and F. J. Vecchio, “Effect of coarse aggregate grading on the ASR expansion and damage of concrete,” Cem. Concr. Res., vol. 95, pp. 75–83, 2017, doi: 10.1016/j.cemconres.2017.02.022.

H. Hou, “Influence of machine-made sand performance on concrete,” E3S Web Conf., vol. 233, pp. 4–7, 2021, doi: 10.1051/e3sconf/202123301040.

H. Donza, O. Cabrera, and E. F. Irassar, “High-strength concrete with different fine aggregate,” vol. 32, pp. 1755–1761, 2002.

S. Rahman, “Analysis on Compressive Strength of Concrete Using Different Sources of Fine ANALYSIS ON COMPRESSIVE STRENGTH OF CONCRETE USING DIFFERENT SOURCES OF FINE AGGREGATES,” no. January, 2020.

J. P. Gonçalves, L. M. Tavares, R. D. T. Filho, E. M. R. Fairbairn, and E. R. Cunha, “Comparison of natural and manufactured fine aggregates in cement mortars,” vol. 37, pp. 924–932, 2007, doi: 10.1016/j.cemconres.2007.03.009.

A. Moulay-ali, M. Abdeldjalil, and H. Khela, “Case Studies in Construction Materials An experimental study on the optimal compositions of ordinary concrete based on corrected dune sand — Case of granular range of 25 mm,” vol. 14, 2021, doi: 10.1016/j.cscm.2021.e00521.

S. Ramkumar and R. Dineshkumar, “Materials Today : Proceedings Experimental study on impact on fineness of sand and M-sand in M20 grade of concrete,” Mater. Today Proc., no. xxxx, 2019, doi: 10.1016/j.matpr.2019.05.356.

G. Sabih, R. A. Tarefder, and S. M. Jamil, “International Conference on Sustainable Design , Engineering and Construction performance as fine aggregate in concrete,” Procedia Eng., vol. 145, pp. 66–73, 2016, doi: 10.1016/j.proeng.2016.04.016.

B. of I. S. (BIS), “IS 383: 1970 Specification for Coarse and Fine Aggregates From Natural Sources for Concrete,” Indian Stand., pp. 1–24, 1970.

M. Kisan, S. Sangathan, J. N`ehru, and S. G. Pitroda, “मनक,” 1988.

Shwetasaibal Samanta Sahoo; Mousime Xalxo; B G Mukunda. "A Study on Tourist Behaviour Towards Sustainable Tourism in Karnataka". International Research Journal on Advanced Science Hub, 2, 5, 2020, 27-33. doi: 10.47392/irjash.2020.28

Muniyandy Elangovan; Mohamed Yousuf; Mohamed Nauman; Mohammed Nayeem. "Design and Development of Delivery Robot for Commercial Purpose". International Research Journal on Advanced Science Hub, 4, 07, 2022, 192-197. doi: 10.47392/irjash.2022.047

Manikandan N; Swaminathan G; Dinesh J; Manish Kumar S; Kishore T; Vignesh R. "Significant Attention in Industry and Academia for Wire Arc Additive Manufacturing (WAAM) - A Review". International Research Journal on Advanced Science Hub, 4, 07, 2022, 198-204. doi: 10.47392/irjash.2022.048

Shoeb Ahmed Syed; Steve Ales; Rajesh Kumar Behera; Kamalakanta Muduli. "Challenges, Opportunities and Analysis of the Machining Characteristics in hybrid Aluminium Composites (Al6061-SiC-Al2O3 ) Produced by Stir Casting Method". International Research Journal on Advanced Science Hub, 4, 08, 2022, 205-216. doi: 10.47392/irjash.2022.051

Ashima Saxena; Preeti Chawla. "A Study on the Role of Demographic Variables on Online Payment in Delhi NCR". International Research Journal on Advanced Science Hub, 4, 08, 2022, 217-221. doi: 10.47392/irjash.2022.052

Vishnupriya S; Nirsandh Ganesan; Ms. Piriyanga; Kiruthiga Devi. "Introducing Fuzzy Logic for Software Reliability Admeasurement". International Research Journal on Advanced Science Hub, 4, 09, 2022, 222-226. doi: 10.47392/irjash.2022.056

GANESAN M; Mahesh G; Baskar N. "An user friendly Scheme of Numerical Representation for Music Chords". International Research Journal on Advanced Science Hub, 4, 09, 2022, 227-236. doi: 10.47392/irjash.2022.057

Nirsandh Ganesan; Nithya Sri Chandrasekar; Ms. Gokila; Ms. Varsha. "Decision Model Based Reliability Prediction Framework". International Research Journal on Advanced Science Hub, 4, 10, 2022, 236-242. doi: 10.47392/irjash.2022.061

Vishnupriya S; Nithya Sri Chandrasekar; Nirsandh Ganesan; Ms. Mithilaa; Ms. Jeyashree. "Comprehensive Analysis of Power and Handloom Market Failures and Potential Regrowth Options". International Research Journal on Advanced Science Hub, 4, 10, 2022, 243-250. doi: 10.47392/irjash.2022.062

Minh Duc Ly; Que Nguyen Kieu Viet. "Improvement Productivity and Quality by Using Lean Six Sigma: A Case Study in Mechanical Manufacturing". International Research Journal on Advanced Science Hub, 4, 11, 2022, 251-266. doi: 10.47392/irjash.2022.066

Ragunath A; Poonam Syal. "Net Zero Energy Buildings Initiatives - A Review". International Research Journal on Advanced Science Hub, 4, 11, 2022, 267-271. doi: 10.47392/irjash.2022.067

Suresh P; Justin Jayaraj K; Aravintha Prasad VC; Abishek Velavan; Mr Gokulnath. "Deep Learning for Covid-19 Identification: A Comparative Analysis". International Research Journal on Advanced Science Hub, 4, 11, 2022, 272-280. doi: 10.47392/irjash.2022.068

Chirag H B; Darshan M; Rakesh M D; Priyanka D S; Manjunath Aradya. "Prediction of Concrete Compressive Strength Using Artificial Neural Network". International Research Journal on Advanced Science Hub, 4, 11, 2022, 281-287. doi: 10.47392/irjash.2022.069

Minh Ly Duc; Que Nguyen Kieu Viet. "Analysis Affect Factors of Smart Meter A PLS-SEM Neural Network". International Research Journal on Advanced Science Hub, 4, 12, 2022, 288-301. doi: 10.47392/irjash.2022.071

Lely Novia; Muhammad Basri Wello. "Analysis of Interpersonal Skill Learning Outcomes in Business English Students Class". International Research Journal on Advanced Science Hub, 4, 12, 2022, 302-305. doi: 10.47392/irjash.2022.072

Ms. Nikita; Sandeep Kumar; Prabhakar Agarwal; Manisha Bharti. "Comparison of multi-class motor imagery classification methods for EEG signals". International Research Journal on Advanced Science Hub, 4, 12, 2022, 306-311. doi: 10.47392/irjash.2022.073

Aniket Manash; Ratan Kumar; Rakesh Kumar; Pandey S C; Saurabh Kumar. "Elastic properties of ferrite nanomaterials: A compilation and a review". International Research Journal on Advanced Science Hub, 4, 12, 2022, 312-317. doi: 10.47392/irjash.2022.074

Prabin Kumar; Rahul Kumar; Ragul Kumar; Vivek Rai; Aniket Manash. "A Review on coating of steel with nanocomposite for industrial applications". International Research Journal on Advanced Science Hub, 4, 12, 2022, 318-323. doi: 10.47392/irjash.2022.075

Twinkle Beniwal; Vidhu K. Mathur. "Cloud Kitchens and its impact on the restaurant industry". International Research Journal on Advanced Science Hub, 4, 12, 2022, 324-335. doi: 10.47392/irjash.2022.076

T. Pravin, C. Somu, R. Rajavel, M. Subramanian, P. Prince Reynold, Integrated Taguchi cum grey relational experimental analysis technique (GREAT) for optimization and material characterization of FSP surface composites on AA6061 aluminium alloys, Materials Today: Proceedings,Volume 33, Part 8, 2020, Pages 5156-5161, ISSN 2214-7853. doi.org/10.1016/j.matpr.2020.02.863.

R. Ranjith, C. Somu, G. Tharanitharan, Venkatajalapathi.T, Naveenkumar M, Integrated Taguchi cum Grey Relational Experimental Analysis (GREAT) for Optimization and Machining Characterization of Cryogenic Cooled AA6063 Aluminium Alloys, Materials Today: Proceedings, Volume 18, Part 7, 2019,Pages 3597- 605, https://doi.org/10.1016/j.matpr.2019.07. 291.

R. Devi Priya, R. Sivaraj, Ajith Abraham, T. Pravin, P. Sivasankar and N. Anitha. "Multi-Objective Particle Swarm Optimization Based Preprocessing of Multi-Class Extremely Imbalanced Datasets". International Journal of Uncertainty, Fuzziness and Knowledge-Based Systems Vol. 30, No. 05, pp. 735-755 (2022). Doi: 10.1142/S0218488522500209

M. S. N. K. Nijamudeen, G. Muthuarasu, G. Gokulkumar, A. Nagarjunan, and T. Pravin, “Investigation on mechanical properties of aluminium with copper and silicon carbide using powder metallurgy technique,” Advances in Natural and Applied Sciences, vol. 11, no. 4, pp. 277–280, 2017.

Pravin T, M. Subramanian, R. Ranjith,Clarifying the phenomenon of Ultrasonic Assisted Electric discharge machining, “Journal of the Indian Chemical Society”, Volume 99, Issue 10, 2022, 100705, ISSN 0019-4522, Doi: 10.1016/j.jics.2022.100705

V.S. Rajashekhar; T. Pravin; K. Thiruppathi , “Control of a snake robot with 3R joint mechanism”, International Journal of Mechanisms and Robotic Systems (IJMRS), Vol. 4, No. 3, 2018. Doi: 10.1504/IJMRS.2018.10017186

T. Pravin, M. Sadhasivam, and S. Raghuraman, “Optimization of process parameters of Al-10% Cu compacts through powder metallurgy,” Applied Mechanics and Materials, vol. 813-814, pp. 603–607, 2010.

Rajashekhar, V., Pravin, T., Thiruppathi, K.: A review on droplet deposition manufacturing-a rapid prototyping technique. Int. J. Manuf. Technol. Manage. 33(5), 362–383 (2019) https://doi.org/10.1504/IJMTM.2019.103277

Rajashekhar V S, Pravin T, Thirupathi K, Raghuraman S.Modeling and Simulation of Gravity based Zig-zag Material Handling System for Transferring Materials in Multi Floor Industries. Indian Journal of Science and Technology.2015 Sep, 8(22), pp.1-6.

How to Cite This Article:
Ganesh Tapkire, Dr. Shashi Ranjan kumar . The Impact of Gradation and Fineness Modulus of Recycled Mortar Sand on the Performance of Cement . ijetms;7(2):403-409. DOI: 10.46647/ijetms.2023.v07i02.048